Skip to content

Changes

View changes from to


On January 30, 2023 at 4:35:29 PM +0200, Gravatar hylli:
  • Updated description of Kampusareena building automation from

    Measurements from the Siemens Desigo building automation system of Kampusareena including data related to indoor conditions, ventilation, heating and cooling. For most spaces in Kampusareena available data includes temperature, air quality and occupancy. This data has been collected so that a new value for a measurement is obtained only when the value changes. Thus the time interval between values varies greatly. It can be anything from less than a second to one day. See the [ProCem](https://ckan.energydata.rd.tuni.fi/organization/about/procem) project for general information about how the measurements are stored and can be used. See the [Kampusareena](https://ckan.energydata.rd.tuni.fi/group/about/kampusareena) group for general information about the building. Note: This is not fully documented for example available measurements are missing.
    to
    Measurements from the Siemens Desigo building automation system of Kampusareena including data related to indoor conditions, ventilation, heating and cooling. For most spaces in Kampusareena available data includes temperature, air quality and occupancy. This data has been collected so that a new value for a measurement is obtained only when the value changes. Thus the time interval between values varies greatly. It can be anything from less than a second to one day. NOTE: IN the available measurements lists some measurements are marked confidential. They are related to spaces used by private tenants of Kampusareena. Extra care has to be taken when using this data. Tenants cannot be identifiable from anything produced from the data. The measurements are organized in a hierarchy that consists of 4 components. These are listed for each measurement in the available measurements lists and are the following: - System: The wider system or subject the measurement is related to. For example water or HVAC (heating, ventilation and air conditioning). - subsystem: Indicates the part of the wider system. For example KL01 (district heating) or iv01 (Air conditioning heating/cooling network). Names are often directly from the building automation system and their meaning is hard or impossible to understand. A list of possible values can be found from below. - location: Indicates the physical location or target of the measurement. Can be a room number or name of a part of a system. - type: Indicates what is measured for example temperature or pressure. ## System System can be one of the following: - HVAC: Heating, Ventilation, and Air Conditioning - Weather - Water - Alarms ## Subsystem Here are listed some of the common subsystems with their descriptions: - TK01-13: Air supply unit - PKxx: Air removal unit; - KK16-17: Air circulating unit - WJ01-02: Chiller for PV01, IV01, SA01 & PK01 - HI01-02: Lifts - IV01: Air conditioning heating/cooling network - KL01: District heating - LV01-02: Hot water network (LV01, LV02) - PV01: Radiator heating/cooling network, wall radiators - PK01: Convector heating/cooling network; - BAS: Building automation system - KV01: Cold-water network - VAKxx: Building automation system CPU - PVPlant: Solar power system - Ventilation ## Location Below are listed some common locations or location types. - Axxx: Room number xxx - LJH: Heat distribution room - Outdoor - Solar - HI01-02: elevator Locations for the subsystems TK01-TK13: - Fans  - HeatRecovery: LTO - Radiator, Air flow heating/cooling Locations related to subsystems TK10-TK11 (Swegon Wise, huonekohtainen ilmamääränsäätö 3nd - 8th floors) - Zone1-6 (Zone 1 = 8th floor, zone 2 = 7th floor,…, zone 6 = 3th floor) - DCxy (x = zone, y = branch ) Locations related to subsystem Chillers (WJ01-WJ02): - Compressors - Condenser - Evaporator - SAPA01: Radiator heating/cooling network, wall radiators & ceiling panels - PK01: Convector heating/cooling network - IV01: Air conditioning heating/cooling network - TC: Chiller temperature controller (WJ01-02) ## Type Here is a list of some common measurement types and the locations or subsystems they usually are associated with. - SP: setpoint, controller target value - AirFlow - AirFlowCoolingSP - Alarm - Angle - Booster - BypassDamper (Heat recovery) - CO2 - ControlState (Heat recovery) - CoolingDemand (VAKs to WJ01-02) - CoolingSP - CoolingState (Heat recovery) - CoolingValve - Damper - DuctPressure - DuctPressureSP - Efficiency (Heat recovery) - ExhaustTemperature - ExtractAirDamper (Fans) - FlowSP - FrequencySP - FreshAirDamper (Fans) - HeatingSP - HeatingValve - Humidity - Illuminance - Power - Presence - Pressure - PressureDifference - RoomTempAverage - RoomTemperature - RoomTempSP - RunState (Heat recovery) - SFP: Specific fan power - SpeedControl - Temperature - TemperatureSP - WaterFlow - VOC: Volatile organic compounds ## Name Measurement names are based on their names in the building automation system. For example a wall mounted temperature sensor can be found from the measurement list based on the text on it for example TCA514'TE20. This example sensor is the temperature sensor TE20 for the temperature controller TC of room A514. If there would be a second similar sensor for the same location it would be called TCA514'TE21. Third would be TE22 and so forth. Second example TK08'TF01'Pwr would be power for air suply fan 01 of air suply unit 08. Third example: KJA528'KF01'TV60 is the cooling valve tv60 for air fan 01 of convector A528 Below are listed the most common acronym number combinations used in the names: - IMSxxxx: Air flow control - TCxxxx: Temperature controller - KJxxxx: Convector - FC: Flow controller; FC1x for supply air, FC3x for exhaust air - PFxx: Exhaust air fan - TFxx: Supply air fan - KFxx: Convector air fan - TV4x: Heating valve; % - TV6x: Cooling valve; % - TE2x: Room temperature; C - TE3x, TEh: Duct exhaust air temperature; C - QE3x: Air quality, CO2; ppm - Aqual: Air quality, volatile organic compounds; % (See [this](https://ckan.energydata.rd.tuni.fi/dataset/kampusareena-building-automation/resource/a02949b9-4f79-43e3-abd1-7537e751fc76) for CO2-equivalent conversion) - AO: Controller output (e.g. damper position); % - AI: Controlled variable (e.g. measured airflow); l/s - TRave: Average room temperature; C - Pwr: Power; kW - SolRdn.SolAzmth: Solar azimuth angle; deg - SolRdn.SolEtHor: Solar elevation angle; deg - KS2x: Ventilation extra time switch/booster; bool - FGxx: Fresh/extract air dampers (Fans); bool - HC: Manual airflow setpoint; % - TR: Room temperature; C - SpH: Radiator heating temperature setpoint; C - SpT: Room temperature setpoint; C - SpCM: Airflow cooling setpoint; C - SpC: Radiator cooling temperature setpoint; C - OE2x; Presence sensor; bool - JJakt: Cool demand; bool - PE1xx: Duct pressure, Supply duct; pa - PE3xx: Duct pressure, Exhaust duct; pa - Flow: Airflow; l/s See the [ProCem](https://ckan.energydata.rd.tuni.fi/organization/about/procem) project for general information about how the measurements are stored and can be used. See the [Kampusareena](https://ckan.energydata.rd.tuni.fi/group/about/kampusareena) group for general information about the building.